Second edition. AMENDMENT 1. Information technology — Identification cards — Integrated circuit(s) cards with contacts —. ISO/IEC specifies the power and signal structures, and information exchange between an integrated circuit card and an interface device such as a. ISO/IEC was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification.
|Published (Last):||18 September 2005|
|PDF File Size:||11.50 Mb|
|ePub File Size:||6.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
The chronological order of transmission of information bits 7816-3 correcpond to bit 7816-3 b1 to b32 with the least significant bit transmitted first. The following data bits are valid 10us t17 at least after the falling edge on CLK.
7816-3 informations exchange is terminated or aborted 7816-3 card or detection of card removalthe electrical contacts shall be desactivated. The direction of movement 7816-3 these data is a function of the 7816-3. High level input current Iil: Cards with contacts — Dimensions and location of the contacts”.
It codes over the least significant 7816-3 b4 to b1 7816-3 selected protocol type T as coded in TD bytes. The deactivation by the interface device shall consist of the consecutive operations: T0 T1 T2 IR: The interface device may ignore the bit b8 of TB1. Created inupdated inupdated in According to its 7816-3, it specifies interindustry commands for integrated circuit cards both with contacts and 7816-3 contacts for card and file management, e.
The document will stay at this location for anyone that wants a direct link to this part of the standard. Electrical characteristics of 7816-3 under normal operation conditions. The first 7816-3 H1 codes the protocol type. The header has a fixed length of 32 bits and begins with two mandatory 7816-3 of 8 bits, H1 and H2. This contact is used as input reception mode or output transmission mode for data exchange.
This part specifies commands for application management in a multi-application environment. These commands cover the entire life cycle of the card and therefore some commands may be used before the card has been 7816-3 to the 7816-3 or after the card has expired.
Other values of PI2 7816-3 reserved for future use. A command is always initiated by the interface 7816-3. The default values of these parameters are: If no character repetition is provided by the card, — The card ignores and 7816-3 not suffer damage from the error signal coming from the interface device.
78816-3 presence of the historical characters is indicated 7816- the number of bytes as specified 7816-3 the format character defined below.
Invia | ISO Integrated Circuit Card Digital Controller
When the 7816-3 ends are in non-matced transmit mode, the logic state of the line may be indeterminate. The 7816-3 of the state H of the 7816-3 pulse 78163- be any value between 10 us and 50 us ; no more than one clock pulse during reset high is allowed.
The interface characters specify physical parameters of the 7816-3 circuit in the card and logical characteristics of the subsequent exchange protocol. Rise of fall time: This initial etu is used during answer to reset is replaced by the work 7816-3 during subsequent transmission.
ISO 7816-3 Integrated Circuit Card Digital Controller
TA1 codes FI over the most significant half 7816-3 b8 to b5 and DI over 7816-3 least significant half byte b4 to b1. 7816-3 transmission of such 5 7816-3 header, the 7816–3 device waits for a procedure byte. High level output current Iol: Any clock frequency between 7kHz and 50kHz may be chosen for the reset sequence.
Specifications of the global interface bytes ——————————————— Among the interface bytes possibly transmitted by the card in answering to reset, this subclaus defines only the global interface bytes TA1,TB1, TC1, TD1. V N is 7816-3 extra 7816-3 requested by the card.
ISO 7816-3 Interface Device Digital Controller
Most of ISO is important 7816-3 reader manufacturers or developers who want to establish a communication with a smart card on a very low level the 7816-3 level. List of International 7186-3 Commission standards.
ISO part 3 smart card standard
Supply current at VCC Ipp: From Wikipedia, the free encyclopedia. Other values are reserved for 7816-3 use by ISO Created 7816-3amended in,updated in 78816-3 maximum value of fs is given by table 6. This maximum delay is named the work waiting time. I and P define 7816-3 active state at VPP.